Skip to content
MoralesGarage Door Repair
A stained wood carriage-style garage door with two rows of divided window lites, set beneath weathered cedar shingle siding and a white trim board.

About us

A Nashua garage door shop, working one town at a time

Morales Garage Door Repair is a residential garage door and opener business based at 22 Northwest Blvd in Nashua, covering the Hillsborough County towns around it.

Who you are calling

The person on the phone is the person at your house

There is no dispatch centre between you and the work. That is the whole shape of how we run.

Morales Garage Door Repair does residential garage doors and openers, and nothing else. We do not fit commercial rolling steel, we do not do dock levellers, and we do not sell you a security system on the way out. A garage door is a heavy, spring-loaded assembly bolted to the side of a house, and getting it to open quietly and stop safely for another decade is a full trade on its own.

The work in southern New Hampshire has its own shape. From roughly November to March, the calls change: doors frozen to the slab, springs that finally let go on the first hard morning of the year, cables corroded through at the bottom bracket by the salt that comes off the car, photo eyes fogged over in an unheated garage so the door reverses for no visible reason. From April onwards it becomes rollers, openers, panels and the tune-ups that stop next winter being expensive.

We built the hours around that. Six in the morning to ten at night, seven days a week, because a door that will not close is not a problem that keeps until Monday — it is an open wall on your house in February. If we cannot get to you the same day we will say so on the call rather than book you and let the evening go quiet.

We are not the cheapest quote you will get. What we are is specific: we tell you what has failed, what it will cost, and what we would do if it were our own door — including the times when the honest answer is that a repair is not worth it, or that the door is fine and you have a frozen bottom seal rather than a broken anything.

How a job runs

Three steps, in this order, every time

Step One

You describe it, we narrow it down

On the phone we ask three or four specific things: what noise it made, how far it travels, whether it lifts by hand with the release pulled, and what the weather was doing when it started. Between those answers, most faults are down to one or two candidates before anyone leaves.

Step Two

We look at the whole door, then quote

At the house we test spring balance with the opener disconnected, check both cables end to end, look at the drums, the rollers, the hinges and the track, and only then write a price for the whole job. The price covers parts, labour and taking the old hardware away.

Step Three

We fix it and set it up properly

The repair is only half of it. Travel and force limits get set, the safety reverse is tested on a flat board, the door is balanced so the opener is not carrying weight it should not, and everything is lubricated with a proper garage door lubricant. Then we show you what we did.

From the work

What the inside of the job looks like

Springs, cables, tracks and head units. Almost everything that goes wrong with a garage door is above your head and behind the door you look at from the drive.

A torsion shaft running the full width of a garage door header above a row of arched window lites, the opener rail crossing beneath a timber ceiling joist.
The torsion shaft above the opening. This is where the door's weight is actually carried.
An extension spring hooked to a pulley above the horizontal track of a garage door, the doubled lift cable running away from it along a white ceiling.
An extension spring, pulley and lift cable on an older door — the arrangement we fit containment cables to.
A garage door opener arm bolted through a reinforcing bracket on the top section of the door, the red and white emergency release cord hanging beside it and the torsion shaft running along the header behind.
The door arm and the emergency release. Pulling this cord is the first thing to try on a frozen morning.
A LiftMaster wall control button mounted beside the light switches on a garage wall, its low-voltage bell wire stapled up towards the ceiling.
The wall control. Half the openers we are called to are diagnosed from this button and the sensor lights.

Towns we cover

Nashua, Hudson, Merrimack, Amherst, Milford and Hollis, New Hampshire. Elsewhere in Hillsborough County, phone and ask — we will give you a straight yes or no on the call.

  • Nashua, NH
  • Hudson, NH
  • Merrimack, NH
  • Amherst, NH
  • Milford, NH
  • Hollis, NH

Ask us what we would do with your door

Even if you are only working out whether it is a repair or a replacement, the call costs nothing and we will tell you what we actually think.

Monday to Sunday, 6:00 AM to 10:00 PM

Call (603) 709-6638